⎝⎛体育滚球平台⎞⎠

Welcome to the official website of Xinhui Valve Co., Ltd.!
  • Xinhui Valve Network
  • China · Xinhui Valve Co., Ltd.

    Phone: 0577-57760066 57760077
    Fax: 0577-57760099
    Website: http://ozarkdirt.com
    QQ: Click here to send me a message
    Address: Xiaojingyu Industrial Zone, Qiaoxia Town, Yongjia County, Zhejiang Province
    Extraction check valve H664
    Extraction check valve H664

    ,快速关闭逆止阀,快关阀 , Extraction check valve , quick closing check valve, quick closing valve ,

    Connection form: welding  
    Material: carbon steel, stainless steel  
    50~1000mm Nominal diameter: 50 ~ 1000mm  
    : 水,蒸汽 Adaptation medium : water, steam  
    0.6-10Mpa Pressure environment: 0.6-10Mpa
    抽汽止回阀产品综述 [ Summary of Extraction Check Valve Products ]
     
    抽汽止回阀 是利用引进技术,在国外同类产品的基础上,采用目前最先进的设计、制造、材料技术、重新开发的完全满足国内 600MW 1000MW 以下发电机组汽轮机抽汽系统需要的阀门产品,技术性能达国际先进水平,为国内外近百家电力企业提供了数百台质优价廉的产品,得到了众多用户的一致好评,已经替代部分进口,为国家节约了大量外汇。 The company's design and production of extraction steam check valve is based on similar foreign products, using the most advanced design, manufacturing, material technology and re-development to fully meet the domestic extraction of steam turbines of 600MW and below The valve products required by the system have reached the international advanced level of technical performance. They have provided hundreds of high-quality and low-cost products to nearly a hundred power companies at home and abroad, and have been well received by many users. They have replaced some imports and saved the country. A lot of foreign exchange. 600MW 以下火力发电汽轮机抽汽系统,防止介质或水倒流,对汽轮机水泵等重要设施起到保护作用。 This series of products are mainly used in the steam extraction system of thermal power generating steam turbines below 600MW to prevent the medium or water from flowing backward and protect important facilities such as steam turbine water pumps. 0.5 秒。 The performance requirements are that the valve closes instantly and the closing time is less than 0.5 seconds under abnormal conditions such as pipeline backflow, power failure, and accident .
    The company's perfect quality assurance system has provided strong protection for high-quality products. The company's quality assurance equipment is complete, the quality assurance system operates healthily and effectively, ensuring product quality is guaranteed, and customer feedback is very good.
    抽汽止回阀设计制造检验标准 [ Design and manufacturing inspection standard for extraction check valve ]
    ASME/ANSIB16.34 E101 JB/T3595 Design and manufacturing standards: ASME / ANSIB16.34 , E101 , JB / T3595
    JB/T3595 ASME/ANSIB16.10 GB/T12221 Structure length standard: JB / T3595 , ASME / ANSIB16.10 , GB / T12221
    GB/T12224 ASME/ANSIB16.25 GB/T9113 JB/T79~JB/T82 Welded end or flange standards: GB / T12224 , ASME / ANSIB16.25 , GB / T9113 , JB / T79 ~ JB / T82
    JB/T9092 JB/T3595 ASME/ANSIB16.34 E101 Test acceptance standards: JB / T9092 , JB / T3595 , ASME / ANSIB16.34 , E101
    抽汽止回阀特点 [ Features of Extraction Check Valve ]
    设计制造验收标准采用 ANSIB16.34 E101 JB/T3595 ,强度及密封性能完全符合标准需要, ►Design and manufacture acceptance standard adopts ANSIB16.34 , E101 or JB / T3595 . The strength and sealing performance fully meet the requirements of the standard.  
    真空状态下的阀门进行真空试验,整机寿命满足用户要求; ►Vacuum test of the valve under vacuum, the life of the whole machine meets user requirements;
    针对不同温度,主体材料采用碳钢或高温钢,密封面堆焊硬质合金; ►For different temperatures, the main material is made of carbon steel or high temperature steel, and the sealing surface is overlaid with hard alloy;
    阀瓣设计为经摇杆与阀杆活动连接,可与阀认密封面自对对中,保证密封面吻合; ►The valve disc is designed to be movably connected to the valve rod via a rocker, which can be self-aligned with the sealing surface of the valve to ensure that the sealing surface is consistent;
    阀座密封面倾斜一定角度,减少关闭时间,减轻冲击,保护设备本身和管道安全; ►The sealing surface of the valve seat is inclined at a certain angle to reduce the closing time, reduce the impact, and protect the safety of the equipment and the pipeline;
    阀门配有阻尼重锤,可平衡关闭件动力矩,防止不锤的发生; ►The valve is equipped with a damping weight, which can balance the dynamic moment of the closing part to prevent the occurrence of non-hammer;
    阀体内腔采用流线型设计,流通能力大,减小阀门阻力; ►The internal cavity of the valve adopts a streamlined design, which has a large flow capacity and reduces the valve resistance;
    执行机构为弹簧复位式气缸或液压缸,并与阀门关闭件动作相对独立,执行机构故障不影响关闭件动作; ►The actuator is a spring-return type or hydraulic cylinder, and is relatively independent of the action of the valve closing member. The failure of the actuator does not affect the action of the closing member;
    气缸戒液压缸内壁涂耐磨耐蚀层,可增加寿命,减轻动作阻力,使阀门灵活、可靠; ►The inner wall of the cylinder or hydraulic cylinder is coated with abrasion-resistant and corrosion-resistant layer, which can increase the life, reduce the action resistance, and make the valve flexible and reliable;
    关闭件开启设有限位机构,避免开启过位造成损坏; ►The closing part is provided with a limit mechanism to avoid damage caused by over-opening;
    执行机构配有阀门开关位置信号输出、阀门开启位置就地指示; ►The actuator is equipped with a valve switch position signal output and a local indication of the valve opening position;
    也可根据用户具体要求进行针对性设计。 ►It can also be designed according to the specific requirements of users.
    用途 及性能规范 [ Application and performance specification of extraction check valve ]
    阀用于电厂或热电厂抽气系统,或其它系统的和水等非腐蚀性介质管道上,防止汽轮机级负荷时汽轮机内的压力突然降低,抽汽管和各加热器内蒸汽倒流进入汽轮机内造成汽轮对片打碎,毁坏汽轮发电机的恶性事故,并防止加热器系统管道泄漏使水从抽汽紧密的关闭,确保在给水加热器出现水位超高时,气动装置部件接到液体逆流信号后,将汽轮机迅速隔开,给汽轮机或抽气系统以最大保护。 H664Y valve is used in the exhaust system of power plant or thermal power plant, or other systems and non-corrosive medium pipes such as water, to prevent the pressure in the steam turbine from suddenly dropping when the turbine stage load, the steam in the extraction pipe and each heater flows back into the turbine Causes the vicious accident of the steam turbine shattering, destroying the steam turbine generator, and prevents the heater system pipeline from leaking and tightly closing the water from the steam extraction, ensuring that when the water level of the feed water heater is too high, the components of the pneumatic device receive After the backflow signal, the turbine is quickly separated to provide maximum protection to the turbine or extraction system.

    Product number
    Pressure Level
    Strength test pressure
    Seal test pressure
    Applicable medium temperature
    Cylinder air source pressure
    H664Y-150Lb
    150Lb
    3.0Mpa
    2.2Mpa
    ≤425
    0.6Mpa
    H664Y-150LbC6
    150Lb
    3.0Mpa
    2.2Mpa
    ≤510
    0.6Mpa
    H664Y-300Lb
    300Lb
    7.5Mpa
    5.5Mpa
    ≤425
    0.6Mpa
    H664Y-600Lb
    600Lb
    15.0Mpa
    10.0Mpa
    ≤425
    0.6Mpa
    H664Y-900LbC6
    900Lb
    24.0Mpa
    18Mpa
    ≤510
    0.6Mpa
    H664H-20
    2.0Mpa
    3.0Mpa
    2.2Mpa
    ≤425
    0.6Mpa
    H664H-50
    5.0Mpa
    7.5Mpa
    5.5Mpa
    ≤425
    0.6Mpa
    H664H-100
    10.0Mpa
    15.0Mpa
    11.0Mpa
    ≤425
    0.6Mpa
    H664Y-64C6
    6.4Mpa
    9.6Mpa
    7.1Mpa
    ≤510
    0.6Mpa
    H664Y-100C6
    10.0Mpa
    15.0Mpa
    11.0Mpa
    ≤510
    0.6Mpa
    H764H-20
    2.0Mpa
    3.0Mpa
    2.2Mpa
    ≤425
    (液压) 0.6Mpa (hydraulic)
    H764H-40
    4.0Mpa
    6.0Mpa
    4.4Mpa
    ≤425
    0.6Mpa
    H764H-64
    6.4Mpa
    9.6Mpa
    7.1Mpa
    ≤425
    0.6Mpa

    下一页: Previous : Exhaust check valve H664Y-P55100V Next :
    欢乐拼三张 七乐彩 欢乐拼三张 真人游戏平台注册